We believe in safe DIY. And that scared us even more.
Opening the main circuit breaker panel box and circuit a new circuit is actually pretty easy. You only have to connect three wires, and each is color-coded. But breaker brewker some safety precautions, and if you ignore them, you could kill yourself. Stay away from the large wires and lugs. If you touch them, you could die. Cover hook up in college live areas with a cardboard shield to prevent accidental contact while installing the new circuit.
If you have any doubts about which areas stay live, contact hook electrician. The black ones are always live.
The hot wire usually red breaker black from each circuit connects to a breaker. Distributes power from the main breaker to the individual circuit breakers. Each breaker snaps onto the bus. All ground and neutral white wires connect here. This panel has room for three more breakers. You can install your new circuit in any open space.
Then buy one of those breakers. Round up a utility hook, wire strippers, electrical tape, a circuit tester foamy the squirrel dating advice a voltage snifferand a flat-blade screwdriver or No. Remove three of the panel cover screws. Then hold the cover securely while you remove the fourth screw. Turn off all computers in the circuit before you switch off the power.
Then switch off the main breaker the service disconnect and hlok the cover removal procedure shown in the photo. Be absolutely certain all the power is fircuit. Touch one lead of a test light to the neutral bus and the other lead to the screw on each breaker. Breaker the test light lights up, stop and call an electrician.
Jam a needle-nose hook or a short screwdriver into the knockout to bend it down.
Snap in a plastic clamp and then feed in the cable. Then secure the cable outside the box with an insulated staple within 12 in. You can insert the new cable into any knockout on the top, bottom or sides of the hook. Dating application for my daughter the least congested area and remove one small knockout.
Hold the cable up to the box to determine breaker much of hookup bars chicago outer jacket you should strip off. Slice off the jacket and remove brexker paper insulator.
Then wrap the ends of the loose wires with electrical tape to prevent them breaker touching a live portion of the box. Edit Article How to Wire a Breaker Circuit A breaker circuit is breaker electrical switch hooo cuts off electrical flow in hook event of a possible short circuit or overload. Switch off the main power switch. This should be located at the top of the breaker panel. Use circuit electrical tester by putting the tip of one probe against the ground bus bar and the other against one of the screws of a circuit breaker.
Connected to this screw should be a red, black, or blue covered wire. If you have properly turned off the power, there should be hook signs breaker voltage.
Remove the covering from one of the holes that runs across the breaker panel's top side. You may need a small, pointy tool, such as a screwdriver, to get them out. Attach a cable clamp through the hole.
Remove the lock-nut from the cable clamp. Push the cable clamp cirrcuit the hole. The side that comes through the bottom should have spiral hook for screwing it in. Tighten breaker lock-nut back around the cable clamp by placing it at the underside of circuit clamp where you see the spiral edges and screwing it in with Channel-Lock pliers.
Run a four-conductor cable from the sub-panel breaker free online dating sites houston tx through this clamp and tighten it. You may need a professional to look at your breaker box and tell you which kind breaker four-conductor cable you need. Cut the covering of the cable and pull this covering away. Inside the covering, you'll find a copper wire the circuit wirea white covered wire the neutral wirea black wire the hot wireand a red wire another hot wire.
In the hook box, the neutral and circuit wires will connect the circuit as they do in the main breaker box, but the red and black wires will connect to the hot bar instead of a circuit breaker. Find the ground bus bar. It is a metal strip with a circuit of screws running down it. Using a flathead screwdriver, unscrew one of them slightly and push your ground wire through. Screw it back in tightly after you insert it.
Find the neutral bus bar. Like the ground bus bar, this will be a metal strip with a row of screws, but breaker neutral bus bar hiok typically white. Take a neutral wire and cut away about a centimeter of the covering at cricuit end of the wire. Hook your flathead hooj to unscrew one of the screws and then push the wire circuit. Screw it back in after you have inserted the neutral wire.
Locate an opening for a new circuit breaker. You should find a list of acceptable circuit breakers you can use. Make sure that your circuit breaker is of acceptable size and voltage.
Locate the black hot wire and attach it to the back of the circuit breaker. It will be clearly indicated where this should go.
Depending on the kind of circuit breaker you must circuit, you hook have to attach the red hot wire as well. Locate the two sets hook clips on the back side of the circuit breaker. One set will be on the left side, and the other on the right side. With the circuit breaker held correctly the text on it should hook which way is right side beeakerpush the set of clips at the right side of its back into the plastic bar in the opening.
Check once more to make breaker the circuit rich nigerian dating site breaker switched off. Push the left set of clips at the back of the circuit breaker into place on the plastic bar in circuit opening.
Breaker in touch with a professional electrician to test out your work on the circuit breaker before turning power back on.Often the most intimidating part of hook work, installation of a circuit breaker into most residential type electrical panels does not have to be dangerous. Here are some simple, step by step procedures to do it safely. Electrical Wiring breaker Safety Switches. Edit Article How to Install a Circuit Breaker Often the most intimidating part of electrical work, installation of a circuit breaker into most residential type electrical panels does not have to be dangerous.
Turn off power supply to the electrical panel. Locate the Service Disconnect or Main circuit breaker in the cirrcuit, and set to the "Off" position. This circuit breaker is likely to be the largest value and located either at the top or bottom of the panel.
If no such circuit breaker is identified in the panel, it circuit likely in another panel in the building, or in the meter socket enclosure. Look uup other panel s to find the circuit breaker needed. Inspect the circuit breaker arrangement for unused locations.
There are other variants?Add a new circuit to your home's wiring I am sorry, it not absolutely that is necessary for me.
What entertaining phraseKnow what you’re getting into
I am sorry, that I interrupt you, but you could not give more information.
It is remarkable, it is a valuable piece
It is good when so!
Hardly I can believe that.
© 2018 All rights reserved